Intek 111D Instrukcja Użytkownika Strona 1

WARRANTYIntek, Inc. warrants each Rheotherm product to be free from defectsin material and workmanship under normal use and service, Intek'soblig

- 8 -MAN114 REV C.wpdSECTION 3 ! OPERATION3.1 START UPTypically, the instruments come from the factory set up for the flow range of interest to the cu

- 9 -MAN114 REV C.wpd3. Flow rate display — The standard display is a 3½ digit LED. The left digit shows only 0 or 1.4. Totalizer — The standard total

- 10 -MAN114 REV C.wpd3.4 OUTPUT CURVEFigure 3 (p. 20) is the final linearized output curve for your unit. The instrument has been calibrated overthe

- 11 -MAN114 REV C.wpd

- 12 -MAN114 REV C.wpdSECTION 4 ! MAINTENANCE4.1 GENERAL MAINTENANCECertain precautions should be taken to insure proper performance of all models of

- 13 -MAN114 REV C.wpd4.3 SPARE PARTSThere are no normally recommended spare parts to stock. The transducer and electronics are a matchedset and ther

- 14 -MAN114 REV C.wpdSECTION 5 ! CUSTOMER SERVICEIntek's corporate philosophy is to solve our customer's difficult flow measurement probl

- 15 -MAN114 REV C.wpdSECTION 6 ! CUSTOM INFORMATION6.1 UNIT IDENTIFICATIONModel no.: Serial no.: Customer identification: 6.2 CONFIGURATIONThe conf

- 16 -MAN114 REV C.wpdTABLE II. ORIGINAL CALIBRATION DATAFOR FUNCTIONAL TESTUnit Serial Number - I II III IV V VITEMP)T TP4Linea

- 17 -MAN114 REV C.wpdFigure 1

TABLE OF CONTENTSSECTION 1 ! GENERAL INFORMATION ... - 1 -1.1 INTRODUCTION ...

- 18 -MAN114 REV C.wpdFigure 2. Rheotherm® Signal Conditioner PWB Layout

- 19 -MAN114 REV C.wpdFigure 3. Flow Rate vs. Output CurveJUST A HOLDING SPACE

- 1 -SECTION 1 ! GENERAL INFORMATION1.1 INTRODUCTIONRheotherm® precision flow meters are designed to provide accurate linear or non-linear (depending

- 2 -MAN114 REV C.wpd1.2 DESCRIPTION OF OPERATIONRheotherm flow meters are available with various nonintrusive and intrusive transducer designs, butth

- 3 -MAN114 REV C.wpd4. Check the transducer maximum temperature rating — do not operate a transducer at or subjectit to a temperature above its speci

- 4 -MAN114 REV C.wpdSECTION 2 ! INSTALLATION. IMPORTANT: All transducers have a directional arrow on the tagand/or etched into a metal part. Befor

- 5 -MAN114 REV C.wpdtube transducer, whether flanged or not, must not be used to pull other piping together or tomake up angular mismatch of fittings

- 6 -MAN114 REV C.wpdthe flow sporadic and difficult to measure. Control valves should be placed down stream ofthe sensor.The ideal installation will

- 7 -MAN114 REV C.wpd3. Laboratory — This table-top unit is NEMA 1 only; do not spill liquid on it or use in a wetenvironment. This unit typically ha